Payroll warnings and problems
Updated
Warnings appear under a run after you calculate it, with a count on the run's row. Fix what you can, then press Recalculate. A warning doesn't stop you approving, so read each one first.
If the run has been finalized, you can't recalculate. See Something changed after the run closed below.
What each warning means
"[Name] has no pay set up for this period, so nothing was paid."
They have hours, tips, commission or adjustments but no pay profile covering the period. The warning lists what they would have earned. Set up their pay under Pay Profiles (turn on Show former staff if they have left), with an Effective Start Date on or before the period, then recalculate. If the name is a placeholder column for baths only, see Tips or visits on a placeholder below.
"[Number] time entries in this period are not yet approved and were excluded from this run."
Approve them under Time Management → Time Entries, then recalculate. A reminder: a shift marked Needs review must be edited first.
"[Number] time entries in this period were already paid by another payroll run and were not paid again."
For your information. Nothing needs doing unless you expected those shifts to be paid here.
"[Name]: [number] approved shifts have no clock-out and were not paid."
Fix the clock-out under Time Entries, approve the shift again, then recalculate.
"[Name]: [number] shifts had no hourly rate on file and paid $0."
Their pay profile has a $0 rate, or doesn't cover that date. For a commission-only groomer on Hourly $0, this is expected. Otherwise, check the rate and Effective Start Date.
"[Name]: week of [date] averaged $[rate]/h, under the [source] minimum wage of $[rate]/h."
Alaga added a make-up so the week reaches minimum wage. Check the hours and commission are right. If they are, nothing else is needed.
"[Name]: classification changed during this period… the whole period was paid as…"
Their W-2/1099 or exempt setting changed partway through. The setting in effect at the end of the period was used for the whole period. To avoid this, change classification on the first day of a period, or ask your accountant how to split it.
"An employee has [number] active services (or products) commission plans; only "[plan]" was applied."
Keep one plan per person. Open the person under Commissions and press Change to replace it.
"[Name] is deactivated but their salary has no end date, so a full salary was calculated."
If they left during the period, the full salary is too much. The pay profile screen doesn't have an end-date field yet, so contact support to set their last day, then recalculate. Or correct the amount with a Deduction adjustment after checking with your accountant.
"The business has no 2-letter state on file, so only federal overtime and minimum-wage rules were applied."
Add your state in Business Settings, then recalculate.
"[Name]: adjustment … skipped."
The adjustment has an invalid amount or an unknown type, so it wasn't counted. Void it and add it again.
"Some hours, tips or adjustments could not be marked as paid by this run. Recalculate before approving."
A temporary save problem. Recalculate. If it comes back, contact support.
The pay period hasn't ended yet.
You calculated early. Anything that happens later in the period isn't in the figures. Recalculate after the period ends.
Other messages
Approve says something changed since the last calculation.
Shifts, tips or adjustments appeared in this period, or paid hours were edited, after you calculated. Press Recalculate, check the new figures and approve again.
"Payroll is already approved through [date]. Start this change on [next date] or later."
You tried to change pay on a date already covered by an approved run. Use the date shown. To correct past pay, use an adjustment.
"You cannot approve or reject your own time entry" or "You cannot correct your own time entry".
Ask an owner or another manager.
"This payroll run is locked and cannot be changed."
It has been finalized. See below.
Common problems
The run shows $0, or very little
Usually, nothing has been set up yet:
- Nobody has a pay profile. Check the Not Configured card and read the warnings.
- Shifts aren't approved, or staff don't clock in.
- No commission plans are assigned. Having plans isn't enough. Each person needs one on the Commissions tab, assigned before the period ended.
Fix what applies and press Recalculate.
Someone's hours are short
- A shift with no clock-out isn't paid.
- A rejected or unapproved shift isn't paid.
- Breaks of 20 minutes or more come off. See How pay is calculated.
Commission is missing or low
- The visit wasn't marked completed, or isn't assigned to them.
- No plan was assigned, or it was assigned after the period ended.
- Add-ons aren't included. See Commission plans, rules and assignments.
- The rule's Minimum Price Threshold wasn't met.
Tips are missing
- The person has no pay profile. The warning shows the amount.
- The tip is a cash tip. These appear in exports as reported, but aren't in Gross, because the person already has the money.
- A Square tip was never assigned. Check Reports → End of Day, under Unassigned Square tips.
Tips or visits on a placeholder
If you book into a column that isn't a person, such as one for baths only, tips can land on that column, and visits earn commission for nobody. A placeholder can't have a pay profile, so these tips aren't paid by a run. The run shows it as "has no pay set up".
Use the Who did this? picker at checkout, and choose a real person under Tip goes to.
There's no button to move a tip that's already recorded. To pay it to the right person, add a Bonus adjustment for them, and let your accountant know why. Contact support if you need many corrected.
Something changed after the run closed
There is no automatic catch-up. Hours, tips and commission only count in the run for their own period. Once that run is finalized, anything dated in that period that appears later isn't picked up by a later run. That includes shifts approved late, tips assigned late and visits completed late.
- Approved but not finalized: press Reopen, then Recalculate.
- Finalized: add the amount to the next run as a Bonus adjustment, with a clear description. Tell your accountant, because the hours won't appear in that week's overtime.
This is why you should approve shifts and check End of Day before you calculate.
A refunded tip is still in payroll
Refunding a tip does not reduce the tip in payroll. The tip stays on the person. If it should come back, add a Deduction adjustment on the run, after checking with your accountant. Refunding a service doesn't reduce commission either.
A contractor isn't in the provider file
ADP RUN and Paychex files cover employees only, and Alaga tells you so. Gusto gets a separate contractor file. All contractor payments are on the payroll register and the 1099 contractors export.
Report totals don't match the run
Payroll reports use approved runs for whole pay periods, and an estimate for days no approved run covers. A note at the top of each report says which is which. Calculated runs aren't counted until they're approved.